密閉氣浮式隔油提升設備采用的外裝式波紋管機械密封，靜環選用99.9%化鋁陶瓷，動環采用四氟填充材料（或根據用戶殊工況配其他材質），其特點是耐腐耐磨性密封性好。

1.定期檢查電泵電動機相間及相對地間緣電阻，其値應大于2MΩ，否則應拆機檢修（逬行干燥處理）同時檢查接地是否牢固；2.葉輪和撕裂機構（底座蓋板）之間的間隙為0.3~0.5，在介質中長期使用之后，此間隙可能由于磨損而增大，此時應予以調整，其方法如下：斷幵電源，松幵固定螺釘，將蓋板旋轉個適當的角度即可恢復原間隙；3.電泵多次使用后必須把電泵放入清水中運行數分鐘，防止泵內留下沉積物，以保證電泵的清潔'；4.電泵在規定的介質中正常運行半年后應檢查油室密封狀況，更換10#~30#機油必要時更換機械密封件，對于在惡劣工作條件下使用的電泵，應經常檢修；換油方法如下：把泵放置好，使油室螺塞（位于出水口內側）朝下，放出潤滑油，然后用洗深油清洗油室，再注入適量的油（約70%~80%）再換個新的〇型圈并將螺塞旋緊。如油中發現有水〔奶狀乳化液）按規定沖洗油室井重新裝油，三個星期后必須重新檢查次，如果油又變成乳狀液，機械密封件應行檢查，必要時應予更換（與我廠維修部接洽〕，如自己更換密封件，須做氣密試驗（空氣壓力為0.5kg/cm2)5.萬發生故障，在不能確定原因，幷且按后面提供的排除方法仍不能解決吋，清不要釆取臨時湊的辦法，更不要私自亂拆亂修，而應與我廠維修部門聯系。

1.關閉出口閥門，松開支架與泵體的聯結螺栓，分離泵體與支架。2.松開電機底腳螺栓，拆開電機風罩，松開拉緊螺栓螺母。3.用銅棒敲擊螺母和拉緊螺栓，使葉輪的尾椎與電機軸上的錐套分開。4.拉開電機，葉輪、泵蓋、機械密封、支架各自分離。5.松開機械密封動環的兩只緊固螺釘，可以從葉輪軸上退下機械密封動環，再取下泵蓋，卸下泵蓋上的機械密封壓蓋螺釘，可以從泵蓋上取下機械密封的靜環。氟塑料離心泵用途及特點80FSB-40氟塑料離心泵廣泛應用于：石油化工、制制、有色金屬冶煉、汽車制造的洗工藝、稀土分離、農、染料、、造紙、電鍍、無線電等，適用于輸送清液或者含有少量顆粒（固含量≤5%）的腐蝕性介質。特點：過流部件全部采用氟塑料合金制造，結構緊湊、操作簡單、價格簡單。兩種型號的泵體、葉輪、機封等均可互換使用。

密閉氣浮式隔油提升設備